Share:
Specifications
SKU: 7388094
ARM? Cortex?-A9 Microprocessor IC i.MX6S 1 Core, 32-Bit 800MHz 624-MAPBGA (21x21)
| Parameter | Description | Value |
|---|---|---|
| Part Number | Part Number | MCIMX6S7CVM08AB |
| Package Type | Package Type | BGA (Ball Grid Array) |
| Pin Count | Number of Pins | 921 |
| Operating Temperature Range | Operating Temperature Range | -40°C to +85°C |
| Storage Temperature Range | Storage Temperature Range | -65°C to +150°C |
| Supply Voltage (VDDA) | Analog Supply Voltage | 1.8V ± 5% |
| Supply Voltage (VDDD) | Digital Core Supply Voltage | 1.2V ± 5% |
| Supply Voltage (VDDIO1-4) | I/O Supply Voltage | 1.8V or 3.3V ± 5% |
| Clock Frequency (CPU) | CPU Clock Frequency | Up to 1.2 GHz |
| Memory | On-chip RAM | 8 MB |
| Flash Memory | External Flash Support | Up to 16 GB |
| GPIOs | General Purpose Input/Output Pins | Up to 240 |
| UARTs | Universal Asynchronous Receiver/Transmitter | 4 |
| SPIs | Serial Peripheral Interface | 4 |
| I2Cs | Inter-Integrated Circuit | 4 |
| USB Interfaces | USB OTG (On-The-Go) | 2 |
| Ethernet | Ethernet MAC | 10/100/1000 Mbps |
| CAN Interfaces | Controller Area Network | 2 |
| ADC Channels | Analog-to-Digital Converter Channels | 8 |
| DAC Channels | Digital-to-Analog Converter Channels | 2 |
| PWM Channels | Pulse Width Modulation Channels | 16 |
| DMA Channels | Direct Memory Access Channels | 16 |
| Watchdog Timers | Watchdog Timers | 2 |
| GPIO Interrupts | GPIO Interrupts | Up to 240 |
| Security Features | Security Features | TrustZone, Secure Boot, Hardware Encryption |
| Power Management | Power Management Features | Low Power Modes, Dynamic Voltage Scaling |
| Package Size | Package Size (mm) | 21 x 21 x 1.4 |
Instructions for Use
Power Supply Configuration:
- Connect VDDA to a stable 1.8V supply.
- Connect VDDD to a stable 1.2V supply.
- Connect VDDIO1-4 to either 1.8V or 3.3V, depending on your application requirements.
Clock Configuration:
- Ensure the external crystal oscillator is connected correctly for the desired CPU clock frequency.
- Configure the PLL (Phase-Locked Loop) settings in the software to achieve the required clock speed.
Memory Initialization:
- Initialize the on-chip RAM and configure the external memory interface if using external flash.
Peripheral Configuration:
- Configure the UART, SPI, I2C, USB, Ethernet, CAN, ADC, DAC, PWM, and DMA peripherals as needed.
- Set up GPIO pins for input/output operations and interrupts.
Security Setup:
- Enable TrustZone and secure boot features to protect against unauthorized access and ensure secure firmware updates.
- Utilize hardware encryption for sensitive data.
Power Management:
- Implement low power modes and dynamic voltage scaling to optimize power consumption based on system load.
Thermal Management:
- Ensure adequate heat dissipation by following the recommended PCB layout guidelines, including thermal vias and heatsinks if necessary.
Software Development:
- Use the NXP SDK (Software Development Kit) and development tools like MCUXpresso IDE for programming and debugging.
- Refer to the datasheet and reference manual for detailed register configurations and programming examples.
For more detailed information, refer to the official NXP datasheet and application notes for the MCIMX6S7CVM08AB.
(For reference only)Inquiry - MCIMX6S7CVM08AB
